Honeycomb and SuperDuo bracelet

Step 1 :
To begin, put a pearl of rock in the KO wire that will serve as a support during the work, but that we will remove at the end of the work. I put a rockery and made a half knot that I could easily remove afterwards.

2nd step :
Then put on 4 honeycomb beads .

Step 3:
Make a circle and go back to the first pearl as below.

Step 4:
We will iron the thread in beads 2 and 3.

Step 5:
And our thread comes out of the pearl 3.

Step 6:
Then pass the needle through the top hole of the bead 3 as shown below.

Step 7:
Thread 3 honyecomb beads.

Step 8:
Enter the initial bead again in the opposite hole to form a circle.

Step 9:
Repeat thread in beads 2 and 3.

Step 10:
Then come out of the top hole of the bead 3 as below.

Step 11:
Again put on 3 honeycomb beads.

Step 12 :
Repeat the previous steps until the desired length is achieved. Take into account the margin of the clasp .

Step 13:
Once your length is finished, coming out of the top hole of the last pearl honeycomb, take in your thread 4 seed beads 11/0 .

Step 14 :
Pass the needle into the upper hole of the bead annex (we go down).

Step 15:
Then thread 1 pearl O bead , 1 pearl SuperDuo and again 1 O Bead

Step 16:
Pass your needle to the next bead.

Step 17:
Again, thread 1 O Bead, 1 SuperDuo, 1 O Bead and pass your needle through the next bead.

Step 18:
Repeat the operation throughout the row until the end.

Step 19:
Thread 4 rockeries 11/0

Step 20:
Cross the next honeycomb pearl.

Step 21:
Thread four 11/0 seed beads.

Step 22:
Go through the top hole of the next honeycomb pearl (we go to the other end).

Step 23:
Take with your needle 1 O Bead, 1 SuperDuo, 1 O Bead and proceed to the next honeycomb.

Step 24:
Repeat this process along the entire row until you reach the other end of the bracelet.

Step 25:
Thread four 11/0 seed beads.

Step 26:
Cross the top hole of the honeycomb as below.

Step 27:
Then put 5 seed 11/0 and also take the clasp.

Step 28:
Pass the needle through the opposite hole of the same honeycomb pearl. The idea being to make a circle.

Step 29:
Iron 2 or 3 times on the same beads to secure the clasp.

Step 30:
Then go back to the 4 side rocailles.

Step 31:
Turn the work if it's more comfortable, and iron all the beads in the row making safety knots.

Step 32:
At the other end, go through the 4 rockeries.

Step 33:
Cross the honeycomb.

Step 34:
Thread 4 rockeries, the clasp, 4 rockeries.

Step 35:
Make a circle by passing your needle through the top hole, opposite part of the honeycomb pearl from which you are coming out.

Step 36:
Do not forget to reinforce this part by passing several times in the same pearls of the circle just formed.

Step 37:
Then go to the next 4 lateral rockeries.

Step 38:
Then on some beads and make a security node (3nodes).
Continue the row

Step 39:
At the other end make a last security node and cut the wire.

Step 40:
We still have the thread with the bead. Remove the bead and thread the needle.

Step 41:
Go through the top hole of the bead and tie a knot further to secure the thread. Then cut the thread.